- Full Version
     
     

Condensed Specs.
Part 1 General

1.01 Section Includes
A. Motorized dual rollershade system for complete light control/ blackout and hardware. Shade Type T is translucent, Shade Type O is room darkening

1.02 System Description
A. Motor operated rollershades via low voltage controls.

1.03 Submittals
A. Product data: Submit five copies of manufacturers technical data and installations instructions.
B. Samples: Submit three samples of each shade cloth with complete color swatch.
C. Shop Drawings: Submit drawings of mechanical products with appropriate dimensions.

1.04 Quality Assurance
A. The manufacturer of these products shall show a minimum of 20 years documented experience.
B. The installer shall show a minimum of 3 years experience with these systems.

Part 2 Products

2.01 Manufacturers
A. SOS™ “Sun Or Shade”, a division of Inside Outfitters, Inc.
5725 Avery Rd., Dublin, Ohio 43016
Ph: 800.742.3372, Fx: 877.880.3496, E: info@sos-shades.com

2.02 Materials
A. Shade Fabrics Type T: Translucent fabrics with openness factors of 1-25%. The fabric color shall be selected from standard color line unless SWSPECIALS is selected. SWSPECIALS allows specifier to create custom color (minimum quantities required). The fabric is to be colorfast and shall not be affected by moisture or heat. (Finishes: See Specification Section “TRANSLUCENT FABRICS” for composition and other details)
1. Phifer
2. 3G Mermet
3. Hexcel
4. Verosol: (PVC free)

B. Shade Fabrics Type O:
The fabric shall have a high degree of opacity for effective control of light. The fabric must have sufficient rigidity to insure straight hanging, resist curl, twist, bowing and distortion. It must be dimensionally stable and will not shrink or stretch. The color shall be selected from standard colors. All seams are to be heat-sealed. Sewing is not accepted. (Finishes: See Specification Section “OPAQUE FABRICS”) .

C. Tube: The fabric shades shall be mounted on to 2”, 2 ½” or 3” diameter aluminum tube depending on the width of the shade and fabric chosen for the shade. Custom size tubes available when dictated by size of shade composition.

D. Idler End: Idler end must be spring loaded to provide easy installation and reduce light gap. Static Idler ends will not be accepted.

E. Motor Control Systems: All systems utilize a Somfy “STARHEAD” motor or group of motors, “world’s largest manufacturer of tubular motors”. Roundhead motors shall not be accepted due to increased light gap. All motors are thermally protected, totally enclosed and maintenance free. (SOMFY UL approved motors can be found in the following file numbers: E60495, E60888, E63714) Each Motor is selected appropriately to operate each shade based on size and weight. All systems utilize low voltage controls.
§ Electrical requirements: 120V, one phase 60 hertz. Amp .7-1.8 depending on size of shade.
Choose system below:
1. Simmple System ™
2. Smmart System™
3. GC System “Group Control”
4. IGC System “Individual Group Control”
5. 2-4-1 System

F. Shade Mounting Brackets: Steel, 1/8” thick type as required to suit indicated mounting and necessary torque. Center bracket utilized as needed to suit span, shade weight and indicated mounting. Fascia brackets shall be painted to match Fascia color.

G. Hembar: Shall be a continuous aluminum bar 1” X 3/16” with sufficient weight to allow the shade to close without buckling or sagging.

H. Fascia System (Option): All fascia systems shall be prime painted with baked enamel utilizing the powder paint method to ensure an environmental friendly application. Wet paint method shall not be accepted. (Finishes: See Specification Section “ACCESSORIES”, Fascia Systems for color selection and detail.)

I. Pocket System (Option): This system allows the shade to be recessed into the ceiling. (Finishes: See Specification Section “ACCESSORIES”, Pocket Systems for color selection, size and details.)